All devices
For UCI hardness testers
For Leeb hardness testers
For Crack depth meters
For Flaw detectors
Probe cable for TQ-4C and TQ-4Combi
This cable is purposed to connect the electronic unit of the hardness tester TQ-4C with a UCI probe.
Connection cable suitable for probes:
- Probe A (HV5)
- Probe H (HV1)
- Probe C (HV10)
- Probe K (HV5)
- Probe AL (HV5)
Length – 100 mm. Connector Lemo-Lemo.
The cable is included in the standard delivery of the UCI Hardness tester TQ-4C. It can also be purchased separately.
Adapter “U4” for hardness tester TQ-4C
Adapter “U4” for positioning of probe on flat, curved, cylindrical surfaces.
Minimum diameter of controlled item is 4 mm.
Adapter “U4” is purposed for following UCI probes:
- Probe A (HV5)
- Probe H (HV1)
- Probe C (HV10)
Probe AL (HV5) for hardness tester TQ-4C
Probe AL (HV5) for hardness tester TQ-4C
The 65 mm long tip allows to measure hardness in hard-to-reach areas:
– in small diameter holes up to 62 mm deep,
– between the teeth of the gears,
– in grooves, recesses, etc.
– in small diameter holes up to 62 mm deep,
– between the teeth of the gears,
– in grooves, recesses, etc.
Probe AL (HV5) is purposed for hardness measurement of following:
- Carbonaceous and structural steels;
- Items with surface-hardened layers such as cementation, nitride hardening, high frequency current hardening;
- Heat-proof, corrosion-proof, non-corrosive steels;
- Plated coating (chrome), overlaying;
- Items of complicated configuration.
Advantages
- Stable readings independent from force and time of pressing.
- Easy measuring in hard-to-reach areas.
- Ultra-small control area (from 1 mm).
- Control in slots and blind holes from 5 mm (not provided by rival devices).
- Invisible print on mirror-surface.
- Low sensitivity to the curvative of surface, thickness and weight of product.
Probes characteristics
| Photo | Probe Type/Load | Weight/thickness/ surface roughness of the article under check |
Length/ |
Application |
 |
«А» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 145/26 mm | Solving of main hardness testing tasks |
| «H» 10H/1 kg |
1 kg/2 mm/Ra 0,8 | 145/26 mm | Hardness testing of electroplated coating (chrome, copper, nickel, zinc, tin), thinwalled and small-sized items | |
| «С» 100H/10 kg |
1 kg/4 mm/Ra 3,2 | 145/26 mm | Hardness testing of items with unprepared surface, large items and heavy-duty equipment | |
 |
«К» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 76/33 mm | Hardness testing of inner surface of tubes, tanks and other hard-to-reach areas |
 |
«AL» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 194/26 mm | Hardness testing in hard-to-reach areas as pinholes, grooves, in-between gear teeth zones (length of tip 65 mm) |
ATTENTION! There is a built-in Lemo plug-in in the probe. Connection cable is sold separately.
The design of hardness testers TQ-4C provides full interchangeability of probes!
Probe C (HV10) for hardness tester TQ-4C
Probe C (HV10) is designed for rough surfaces and is purchased separately.
The design of hardness testers TQ-4C provides full interchangeability of probes!
Probe C (HV10) is purposed for hardness measurement of following:
- Carbonaceous and structural steels;
- Items with surface-hardened layers such as cementation, nitride hardening, high frequency current hardening;
- Heat-proof, corrosion-proof, non-corrosive steels;
- Items of complicated configuration;
- Products with rough, poorly prepared surface;
- Thick-walled, large-sized objects.
Advantages
- Stable readings independent from force and time of pressing.
- Easy measuring in hard-to-reach areas.
- Ultra-small control area (from 1 mm).
- Control in slots and blind holes from 5 mm (not provided by rival devices).
- Invisible print on mirror-surface.
- Low sensitivity to the curvative of surface, thickness and weight of product.
Probes characteristics
| Photo | Probe Type/Load | Weight/thickness/ surface roughness of the article under check |
Length/ |
Application |
 |
«А» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 145/26 mm | Solving of main hardness testing tasks |
| «H» 10H/1 kg |
1 kg/2 mm/Ra 0,8 | 145/26 mm | Hardness testing of electroplated coating (chrome, copper, nickel, zinc, tin), thinwalled and small-sized items | |
| «С» 100H/10 kg |
1 kg/4 mm/Ra 3,2 | 145/26 mm | Hardness testing of items with unprepared surface, large items and heavy-duty equipment | |
 |
«К» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 76/33 mm | Hardness testing of inner surface of tubes, tanks and other hard-to-reach areas |
 |
«AL» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 194/26 mm | Hardness testing in hard-to-reach areas as pinholes, grooves, in-between gear teeth zones (length of tip 65 mm) |
ATTENTION! There is a built-in Lemo plug-in in the probe. Connection cable is sold separately.
Probe H (HV1) for hardness tester TQ-4C
Probe H (HV1) is purposed to control hardness of galvanic coatings (chrome, copper, nickel), thin-walled and small-sized items.
The design of hardness testers TQ-4C provides full interchangeability of probes!
Probe H (HV1) is purposed for hardness measurement of following:
- Electroplating (chrome, copper, nickel, zinc, tin, etc.),
- Thin-walled and small-sized products,
- Products from fine-grained materials at local research of properties of materials,
- Items of complicated configuration.
Advantages
- Stable readings independent from force and time of pressing.
- Easy measuring in hard-to-reach areas.
- Ultra-small control area (from 1 mm).
- Control in slots and blind holes from 5 mm (not provided by rival devices).
- Invisible print on mirror-surface.
- Low sensitivity to the curvative of surface, thickness and weight of product.
Probes characteristics
| Photo | Probe Type/Load | Weight/thickness/ surface roughness of the article under check |
Length/ |
Application |
 |
«А» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 145/26 mm | Solving of main hardness testing tasks |
| «H» 10H/1 kg |
1 kg/2 mm/Ra 0,8 | 145/26 mm | Hardness testing of electroplated coating (chrome, copper, nickel, zinc, tin), thin-walled and small-sized items | |
| «С» 100H/10 kg |
1 kg/4 mm/Ra 3,2 | 145/26 mm | Hardness testing of items with unprepared surface, large items and heavy-duty equipment | |
 |
«К» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 76/33 mm | Hardness testing of inner surface of tubes, tanks and other hard-to-reach areas |
 |
«AL» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 194/26 mm | Hardness testing in hard-to-reach areas as pinholes, grooves, in-between gear teeth zones (length of tip 65 mm) |
ATTENTION! There is a built-in Lemo plug-in in the probe. Connection cable is sold separately.
Probe K (HV5) for hardness tester TQ-4C
Probe K (HV5) has reduced dimensions for hardness control in a limited space: inside pipes, tanks and other hard-to-reach places.
The design of hardness testers TQ-4C provides full interchangeability of probes!
Probe K (HV5) is purposed for hardness measurement of following:
- Carbonaceous and structural steels;
- Items with surface-hardened layers such as cementation, nitride hardening, high frequency current hardening;
- Heat-proof, corrosion-proof, non-corrosive steels;
- Plated coating (chrome), overlaying;
- Items of complicated configuration.
Advantages
- Stable readings independent from force and time of pressing.
- The spatial position of the sensor does not affect the measurement result.
- Easy measuring in hard-to-reach areas.
- Ultra-small control area (from 1 mm).
- Invisible print on mirror-surface.
- Low sensitivity to the curvative of surface, thickness and weight of product.
Probes characteristics
| Photo | Probe Type/Load | Weight/thickness/ surface roughness of the article under check |
Length/ |
Application |
 |
«А» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 145/26 mm | Solving of main hardness testing tasks |
| «H» 10H/1 kg |
1 kg/2 mm/Ra 0,8 | 145/26 mm | Hardness testing of electroplated coating (chrome, copper, nickel, zinc, tin), thin-walled and small-sized items | |
| «С» 100H/10 kg |
1 kg/4 mm/Ra 3,2 | 145/26 mm | Hardness testing of items with unprepared surface, large items and heavy-duty equipment | |
 |
«К» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 76/33 mm | Hardness testing of inner surface of tubes, tanks and other hard-to-reach areas |
 |
«AL» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 194/26 mm | Hardness testing in hard-to-reach areas as pinholes, grooves, in-between gear teeth zones (length of tip 65 mm) |
ATTENTION! There is a built-in Lemo plug-in in the probe. Connection cable is sold separately.
Probe A (HV5) for hardness tester TQ-4C
Probe A (HV5) included in the standard delivery of UCI hardness tester TQ-4C.
The design of hardness testers TQ-4C provides full interchangeability of probes!
Probe A (HV5) is purposed for hardness measurement of following:
- Carbonaceous and structural steels;
- Items with surface-hardened layers such as cementation, nitride hardening, high frequency current hardening;
- Heat-proof, corrosion-proof, non-corrosive steels;
- Plated coating (chrome), overlaying;
- Items of complicated configuration.
Advantages
- Stable readings independent from force and time of pressing.
- Easy measuring in hard-to-reach areas.
- Ultra-small control area (from 1 mm).
- Control in slots and blind holes from 5 mm (not provided by rival devices).
- Invisible print on mirror-surface.
- Low sensitivity to the curvative of surface, thickness and weight of product.
Probes characteristics
| Photo | Probe Type/Load | Weight/thickness/ surface roughness of the article under check |
Length/ |
Application |
 |
«А» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 145/26 mm | Solving of main hardness testing tasks |
| «H» 10H/1 kg |
1 kg/2 mm/Ra 0,8 | 145/26 mm | Hardness testing of electroplated coating (chrome, copper, nickel, zinc, tin), thinwalled and small-sized items | |
| «С» 100H/10 kg |
1 kg/4 mm/Ra 3,2 | 145/26 mm | Hardness testing of items with unprepared surface, large items and heavy-duty equipment | |
 |
«К» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 76/33 mm | Hardness testing of inner surface of tubes, tanks and other hard-to-reach areas |
 |
«AL» 50H/5 kg |
1 kg/3 mm/Ra 1,6 | 194/26 mm | Hardness testing in hard-to-reach areas as pinholes, grooves, in-between gear teeth zones (length of tip 65 mm) |
ATTENTION! There is a built-in Lemo plug-in in the probe. Connection cable is sold separately.